If you forgot the password of the BMC, you can run the following command while the host is running to perform a factory reset and to restore the default password: ipmitool raw 0x3A 0x11 You must set up and configure the BMC IP address after performing the factory reset. The first step is to get ipmicfg. To access iDRAC Settings utility, press F2 during boot and then click iDRAC Settings on the System Setup Main Menu page. Supermicro has a package that includes DOS, Windows and Linux versions. Now turn off the DHCP setting restored from factory defaults with./ipmicfg-linux.x86_64 -dhcp off then, restore your network settings with: How to Reset Supermicro IPMI Username and Password to Default. Navigate to Maintenance > Factory Default. IPMIcfg dir listing I had run the following commands via CLI from CENTOS in order to reset the IPMI but it is not working: yum install ipmitool -y modprobe ipmi_devintf modprobe ipmi_si ipmitool -I open user set password 2 ADMIN Could you please give some advice on how can I reset or update the IPMi from CLI CENTOS? Modify boot device for next reboot. Dell BMC is based on iDRAC 8, supporting an optimized for hyper scale, set of features from iDRAC. Here you can find an option to perform iDRAC factory reset (reset to default). Using 'ipmicfg-win.exe -fde' wiped and reset the IPMI configuration, including the network settings, and got it working. You can restore the BMC to its factory-default settings, including deleting the SSL Certificate and SSL key. During Boot you can go to iDRAC Setting utility to perform iDRAC factory reset. Click Restore. To reset the BMC to factory defaults, follow the steps shown below: Click Start to Reset BMC to Factory Defaults. Specifically Dell BMC supports virtual KVM and Media, while the Lifecycle Controller Pre-Boot environment has been removed. I tried changing the IP first to see if that would kickstart it, but it didn't, and there wasn't an option to change the binding. Reset the configuration to factory defaults by using the shell. I've now changed them all to 'dedicated', hopefully it avoids this happening again. The current revision is 1.02. 7. dell ipmitool reset idrac, It is standards based: IPMI 2.0, and DCMI 1.5 compliant. This guide will show how to use a DOS LiveCD or USB to modify IPMI users and reset the IPMI BMC to factory defaults. Being able to perform these tasks in IPMI firmware on the Baseboard Management Controller (BMC) allows OS-independent management. ipmitool [chassis] power cycle # issue a hard power off, wait 1s, power on ipmitool [chassis] power off # issue a hard power off ipmitool [chassis] power on # issue a hard power on ipmitool [chassis] power reset # issue a hard reset. At the shell prompt, type: ipmitool raw 0x30 0x40 What is the difference between Dell BMC & iDRAC? Best way is to reset to defaults and clear FRU&LAN with SuperMicro native tool, like so:./ipmicfg-linux.x86_64 -fde (All this may take a few seconds to take effect, so wait between commands!) Note: Only users with Supervisor user authority level can perform this action. Everything from remote reset/power-off to sending an SNMP alert from a sensor event even if the OS is down. Located below Restore BMC from Configuration File is the Reset BMC to factory default section. Connect to the host via SSH and from the menu select Shells, then boot shell Issue the following command: ipmitool user list Note the ID of the IPMI admin user; Change the password with the following command: ipmitool user set password After this, you should be able to access the IPMI interface with the newly set password. #ipmitool lan set 1 ipaddr xxx.xxx.xxx.xxx #set BMC ip address# #ipmitool lan set 1 netmask xxx.xxx.xxx.xxx #set BMC net mask# #ipmitool -I open user list 1 #find out available users# #ipmitool user set password X new-pass #set password, where X is the ID of the user from above user list# 3. Reset the configuration to factory defaults by using the GUI.